SN74AHC573DWR
| Parameters | |
|---|---|
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AHC573 |
| Pin Count | 20 |
| Output Type | Tri-State |
| Circuit | 8:8 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Latch |
| Current - Output High, Low | 8mA 8mA |
| Logic Type | D-Type Transparent Latch |
| Control Type | ENABLE LOW |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Independent Circuits | 1 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74AHC |
SN74AHC573DWR Overview
In the 20-SOIC (0.295, 7.50mm Width) package, it can be found as an embedded module. Packaged in the way of Tape & Reel (TR). In this configuration, the output is set to Tri-State. A D-Type Transparent Latch logic type is used in this electrical device. According to Surface Mount, this electronic part is mounted. It operates at a voltage of 2V~5.5V. It is -40°C~85°C at the operating temperature. The 74AHC series of FPGAs is the one this FPGA belongs to. An electronic part with 8 bits is designed. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. As a member of the 74AHC573 family, it falls under that category. The device works with a voltage of 3.3V for its supply voltage. The 20 pind are equipped with it. This electronic device belongs to the family of AHC/VHC/H/U/V. The pin configuration of the device is 20. The electronic part is mounted in a way that corresponds to Surface Mount. There are 2 ports, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This part is included in FF/Latches. There is a maximum voltage supply (Vsup) that reaches 5.5V. 2/5.5V power supplies are needed to operate it. (Vsup) should be greater than 2V. It consists of 3 input lines from which an electronic circuit can be built. The device's reliable performance makes it a good choice for TR. The maximal power current (ICC) supplied for its operation reaches 0.04mA.
SN74AHC573DWR Features
20-SOIC (0.295, 7.50mm Width) package
74AHC series
8 Bits
74AHC573 family
20 pin count
20 pins
2/5.5V power supplies
SN74AHC573DWR Applications
There are a lot of Texas Instruments SN74AHC573DWR Latches applications.
- Address register
- Display
- Shift Registers
- Automotive Cluster
- Counting
- Pattern Generators
- PCs and Notebooks
- Timers
- BCD counting
- Hammer Device Information
