SN74AHC574DWRE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Frequency | 115MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Temperature Grade | AUTOMOTIVE |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 8mA |
| Number of Bits | 8 |
| Propagation Delay | 16.7 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Control Type | ENABLE LOW |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHC574DWRE4 Overview
The item is packaged in SOICcases. There is an embedded version in the package Tape & Reel (TR). The number of terminations is 20. The power source is powered by 3.3V. The electronic device belongs to the AHC/VHC/H/U/Vfamily. There is an electronic component mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device exhibits a clock edge trigger type of Positive Edge. It is included in FF/Latches. There are 8bits in this flip flop. Its superior flexibility is attributed to its use of 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It operates with 1 output lines. It is reported that there are 3 input lines. -8mAis the output current at high level. There is no low level output current set at 8mA. Operating temperatures should be lower than 125°C. In order for the system to operate properly, the temperature should be higher than -40°C. A minimum supply voltage of 2V is required for these RS flip flops to operate. It supports the maximal supply voltage of 5.5V. We are able to achieve a frequency of 115MHz. This logic IC is BUS DRIVER. There are 1 functions available on the JK flip flop. This device is equipped with a pin count of 20. As a result of the output current of 8mA, the design flexibility is maximized.
SN74AHC574DWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
1 Functions
20 pin count
SN74AHC574DWRE4 Applications
There are a lot of Texas Instruments SN74AHC574DWRE4 Flip Flops applications.
- Communications
- ESD performance
- Balanced Propagation Delays
- ESCC
- Clock pulse
- Buffer registers
- Divide a clock signal by 2 or 4
- Dynamic threshold performance
- ESD protection
- Safety Clamp
