SN74AHC574PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 16.7 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC574PWR Overview
20-TSSOP (0.173, 4.40mm Width)is the way it is packaged. You can find it in the Cut Tape (CT)package. This output is configured with Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. It is mounted in the way of Surface Mount. A voltage of 2V~5.5Vis used as the supply voltage. A temperature of -40°C~85°C TAis used in the operation. The type of this D latch is D-Type. FPGAs belonging to the 74AHCseries contain this type of chip. Its output frequency should not exceed 115MHz. There are 1 elements in it. Terminations are 20. JK flip flop belongs to 74AHC574 family. The power source is powered by 3.3V. Input capacitance of this device is 3pF farads. It belongs to the family of electronic devices known as AHC/VHC/H/U/V. The electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device has the clock edge trigger type of Positive Edge. This RS flip flops is a part number FF/Latches. An electronic part designed with 8bits is used in this application. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. For normal operation, the supply voltage (Vsup) should be above 2V. Its superior flexibility is attributed to its use of 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. In order for the device to operate, it requires 2/5.5V power supplies. The flip flop has 2ports embedded within it. With a current output of 8mA , it offers maximum design flexibility. It has 3lines. Quiescent current is consumed by the D latch in the amount of 4μA.
SN74AHC574PWR Features
Cut Tape (CT) package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC574PWR Applications
There are a lot of Texas Instruments SN74AHC574PWR Flip Flops applications.
- Registers
- Event Detectors
- Matched Rise and Fall
- ESCC
- Digital electronics systems
- ESD performance
- Data Synchronizers
- Patented noise
- Single Down Count-Control Line
- Divide a clock signal by 2 or 4
