SN74AHCT16374DLG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 130MHz |
| Pin Count | 48 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Prop. Delay@Nom-Sup | 11.5 ns |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Control Type | INDEPENDENT CONTROL |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.59mm |
| Length | 15.88mm |
| Width | 7.49mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHCT16374DLG4 Overview
It is packaged in the way of SSOP. Currently, there are 48 terminations. It is powered by a voltage of 5V . In terms of electronic devices, this device belongs to the AHCT/VHCT/VTfamily of devices. It is mounted in the way of Surface Mount. This board is designed with 48pins on it. It has a clock edge trigger type of Positive Edge. It is included in FF/Latches. The design is based on 16bits. The superior flexibility is achieved through the use of 2 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TUBE. The system runs on a power supply of 5V watts. There are 2 ports embedded in the flip flops. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There are no output lines on the JK flip flop. 8input lines are available for you to choose from. The high level output current is set to -8mA. 8mA is the low level output current. It is recommended that the operating temperature be below 85°C. Operating temperatures should be above -40°C. It operates with the minimal supply voltage of 4.5V. The maximum supply voltage supported by the flip flop is 5.5V. It is possible to obtain a frequency of 130MHz. There is a logic IC BUS DRIVER used in the D flip flop. Currently, it is equipped with 2 functions . This device is equipped with a pin count of 48.
SN74AHCT16374DLG4 Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
SN74AHCT16374DLG4 Applications
There are a lot of Texas Instruments SN74AHCT16374DLG4 Flip Flops applications.
- Frequency Dividers
- Event Detectors
- Single Down Count-Control Line
- CMOS Process
- ESCC
- 2 – Bit synchronous counter
- Cold spare funcion
- Memory
- Clock pulse
- QML qualified product
