SN74AHCT174D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Clock Frequency | 115MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT174D Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. D flip flop is included in the Tubepackage. Currently, the output is configured to use Non-Inverted. There is a trigger configured with Positive Edge. It is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. -40°C~85°C TAis the operating temperature. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74AHCT series. It should not exceed 115MHzin its output frequency. D latch consists of 1 elements. As a result, it consumes 4μA of quiescent current without being affected by external factors. A total of 16terminations have been recorded. D latch belongs to the 74AHCT174 family. A voltage of 5V is used as the power supply for this D latch. There is 2pF input capacitance for this T flip flop. It belongs to the family of electronic devices known as AHCT/VHCT/VT. A part of the electronic system is mounted in the way of Surface Mount. With its 16pins, it is designed to work with most electronic flip flops. In this device, the clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. To achieve this superior flexibility, 7 circuits are used. An electrical current of 5V volts is applied to it. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. With a current output of 8mA , it offers maximum design flexibility. Currently, there are 3 input lines present.
SN74AHCT174D Features
Tube package
74AHCT series
16 pins
5V power supplies
SN74AHCT174D Applications
There are a lot of Texas Instruments SN74AHCT174D Flip Flops applications.
- Frequency Divider circuits
- Power down protection
- QML qualified product
- 2 – Bit synchronous counter
- Safety Clamp
- Communications
- Guaranteed simultaneous switching noise level
- Shift registers
- Balanced 24 mA output drivers
- High Performance Logic for test systems
