SN74AHCT174DGVR
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHCT174 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Clock Frequency | 115MHz |
| Propagation Delay | 8.8 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 3 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
SN74AHCT174DGVR Overview
As a result, it is packaged as 16-TFSOP (0.173, 4.40mm Width). The package Tape & Reel (TR)contains it. The output it is configured with uses Non-Inverted. This trigger uses the value Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. It is operating at a temperature of -40°C~85°C TA. This electronic flip flop is of type D-Type. In FPGA terms, D flip flop is a type of 74AHCTseries FPGA. You should not exceed 115MHzin the output frequency of the device. In total, it contains 1 elements. There is 4μA quiescent consumption. 16terminations have occurred. It is a member of the 74AHCT174 family. A voltage of 5V is used to power it. Its input capacitance is 2pF farads. An electronic device belonging to the family AHCT/VHCT/VTcan be found here. A part of the electronic system is mounted in the way of Surface Mount. The 16pins are designed into the board. This device has the clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Vsup reaches 5.5V, the maximal supply voltage. For normal operation, the supply voltage (Vsup) should be above 4.5V. Its superior flexibility is attributed to its use of 7 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The D latch runs on a voltage of 5V volts. Currently, there are 3 input lines present.
SN74AHCT174DGVR Features
Tape & Reel (TR) package
74AHCT series
16 pins
5V power supplies
SN74AHCT174DGVR Applications
There are a lot of Texas Instruments SN74AHCT174DGVR Flip Flops applications.
- Asynchronous counter
- Safety Clamp
- Data transfer
- Balanced 24 mA output drivers
- Latch
- Bounce elimination switch
- Divide a clock signal by 2 or 4
- Functionally equivalent to the MC10/100EL29
- Reduced system switching noise
- Synchronous counter
