SN74AHCT174DGVRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHCT174 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 115MHz |
| Propagation Delay | 8.8 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Output Lines | 6 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.4mm |
| RoHS Status | ROHS3 Compliant |
SN74AHCT174DGVRG4 Overview
The package is in the form of 16-TFSOP (0.173, 4.40mm Width). It is contained within the Tape & Reel (TR)package. This output is configured with Non-Inverted. This trigger uses the value Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74AHCT series. This D flip flop should not have a frequency greater than 115MHz. D latch consists of 1 elements. As a result, it consumes 4μA of quiescent current without being affected by external factors. There have been 16 terminations. You can search similar parts based on 74AHCT174. A voltage of 5V provides power to the D latch. Its input capacitance is 2pF farads. A device of this type belongs to the family of AHCT/VHCT/VT. There is an electronic part that is mounted in the way of Surface Mount. This board is designed with 16pins on it. This device has the clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part with 6bits has been designed. 5.5Vis the maximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be kept above 4.5V. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. There are 6 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
SN74AHCT174DGVRG4 Features
Tape & Reel (TR) package
74AHCT series
16 pins
6 Bits
5V power supplies
SN74AHCT174DGVRG4 Applications
There are a lot of Texas Instruments SN74AHCT174DGVRG4 Flip Flops applications.
- Cold spare funcion
- Computing
- Memory
- Clock pulse
- Balanced Propagation Delays
- Modulo – n – counter
- Frequency Divider circuits
- Count Modes
- Latch
- Event Detectors
