SN74AHCT174DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Clock Frequency | 115MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT174DR Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. It is included in the package Tape & Reel (TR). This output is configured with Non-Inverted. The trigger it is configured with uses Positive Edge. This electronic part is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Temperature is set to -40°C~85°C TA. This D latch has the type D-Type. In terms of FPGAs, it belongs to the 74AHCT series. It should not exceed 115MHzin its output frequency. A total of 1elements are contained within it. There is a consumption of 4μAof quiescent energy. There have been 16 terminations. This D latch belongs to the family of 74AHCT174. The power source is powered by 5V. The input capacitance of this T flip flop is 2pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the AHCT/VHCT/VTfamily. Electronic part Surface Mountis mounted in the way. It is designed with 16 pins. In this device, the clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. The superior flexibility of this circuit is achieved by using 7 circuits. A reliable performance of this D flip flop makes it well suited for use in TR. The D latch runs on a voltage of 5V volts. Optimal efficiency requires a supply voltage of 5V. The number of input lines is 3.
SN74AHCT174DR Features
Tape & Reel (TR) package
74AHCT series
16 pins
5V power supplies
SN74AHCT174DR Applications
There are a lot of Texas Instruments SN74AHCT174DR Flip Flops applications.
- Power down protection
- Computing
- Pattern generators
- Circuit Design
- Matched Rise and Fall
- Differential Individual
- Patented noise
- Frequency Divider circuits
- Bounce elimination switch
- ATE
