SN74AHCT273DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 75MHz |
| Propagation Delay | 12.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 65 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT273DBR Overview
20-SSOP (0.209, 5.30mm Width)is the way it is packaged. It is contained within the Cut Tape (CT)package. As configured, the output uses Non-Inverted. The trigger it is configured with uses Positive Edge. It is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. A temperature of -40°C~125°C TAis considered to be the operating temperature. A flip flop of this type is classified as a D-Type. It is a type of FPGA belonging to the 74AHCT series. Its output frequency should not exceed 75MHz. In total, it contains 1 elements. T flip flop consumes 4μA quiescent energy. The number of terminations is 20. Members of the 74AHCT273family make up this object. Power is supplied from a voltage of 5V volts. This JK flip flop has a 2.5pFfarad input capacitance. In this case, the D flip flop belongs to the AHCT/VHCT/VTfamily. In this case, the electronic component is mounted in the way of Surface Mount. A total of 20pins are provided on this board. It has a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. Flip flops designed with 8bits are used in this part. Its flexibility is enhanced by 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. A power supply of 5Vis required to operate it. For high efficiency, the supply voltage should be set to 5V. 3input lines are available for you to choose from.
SN74AHCT273DBR Features
Cut Tape (CT) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT273DBR Applications
There are a lot of Texas Instruments SN74AHCT273DBR Flip Flops applications.
- Registers
- Event Detectors
- Functionally equivalent to the MC10/100EL29
- Memory
- Digital electronics systems
- Buffered Clock
- Communications
- Power down protection
- ESD protection
- Balanced Propagation Delays
