SN74AHCT273DW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 75MHz |
| Propagation Delay | 9.2 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 65 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT273DW Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. The package Tubecontains it. T flip flop is configured with an output of Non-Inverted. The trigger configured with it uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. A temperature of -40°C~85°C TAis used in the operation. This D latch has the type D-Type. It belongs to the 74AHCTseries of FPGAs. Its output frequency should not exceed 75MHz Hz. In total, it contains 1 elements. As a result, it consumes 4μA quiescent current. 20terminations have occurred. It is a member of the 74AHCT273 family. Power is supplied from a voltage of 5V volts. A JK flip flop with a 2.5pFfarad input capacitance is used here. In terms of electronic devices, this device belongs to the AHCT/VHCT/VTfamily of devices. It is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device has Positive Edgeas its clock edge trigger type. This part is included in FF/Latches. An electronic part designed with 8bits is used in this application. There are 5V power supplies attached to it. In order to achieve high efficiency, the supply voltage should be maintained at 5V. The output current of 8mA makes it feature maximum design flexibility. As of now, there are 3input lines. There are 8 channels available.
SN74AHCT273DW Features
Tube package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT273DW Applications
There are a lot of Texas Instruments SN74AHCT273DW Flip Flops applications.
- Frequency Divider circuits
- Bounce elimination switch
- Data Synchronizers
- Computing
- Memory
- ATE
- ESD protection
- Bus hold
- Buffered Clock
- Latch-up performance
