SN74AHCT374DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT374DBR Overview
The package is in the form of 20-SSOP (0.209, 5.30mm Width). As part of the package Cut Tape (CT), it is embedded. There is a Tri-State, Non-Invertedoutput configured with it. It is configured with the trigger Positive Edge. This electronic part is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Currently, the operating temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74AHCT series. There should be no greater frequency than 130MHzon its output. In total, it contains 1 elements. This process consumes 4μA quiescents. It has been determined that there have been 20 terminations. You can search similar parts based on 74AHCT374. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 4pFfarads. This D flip flop belongs to the family of AHCT/VHCT/VT. There is an electronic part that is mounted in the way of Surface Mount. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 8bits has been designed. Its superior flexibility is attributed to its use of 8 circuits. In light of its reliable performance, this T flip flop is well suited for TR. The power supply is 5V. This D flip flop is equipped with 0 ports. If high efficiency is desired, the supply voltage should be kept at 5V. This input has 3lines.
SN74AHCT374DBR Features
Cut Tape (CT) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT374DBR Applications
There are a lot of Texas Instruments SN74AHCT374DBR Flip Flops applications.
- Memory
- Computers
- Guaranteed simultaneous switching noise level
- Consumer
- Asynchronous counter
- Power down protection
- Event Detectors
- CMOS Process
- Balanced Propagation Delays
- Divide a clock signal by 2 or 4
