SN74AHCT374DGVR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 60.186038mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74AHCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT374DGVR Overview
In the form of 20-TFSOP (0.173, 4.40mm Width), it has been packaged. Package Cut Tape (CT)embeds it. In the configuration, Tri-State, Non-Invertedis used as the output. It is configured with a trigger that uses Positive Edge. Surface Mountis in the way of this electric part. The JK flip flop operates at a voltage of 4.5V~5.5V. Currently, the operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. It belongs to the 74AHCTseries of FPGAs. It should not exceed 130MHzin its output frequency. A total of 1 elements are present. There is a consumption of 4μAof quiescent energy. 20terminations have occurred. You can search similar parts based on 74AHCT374. The power source is powered by 5V. This JK flip flop has a 4pFfarad input capacitance. This D flip flop belongs to the family of AHCT/VHCT/VT. This electronic part is mounted in the way of Surface Mount. 20pins are included in its design. This device's clock edge trigger type is Positive Edge. It is included in FF/Latches. The flip flop is designed with 8bits. Its flexibility is enhanced by 8 circuits. This D flip flop is well suited for TR based on its reliable performance. A total of 5V power supplies are needed to run it. The D flip flop is embedded with 2ports. Optimal efficiency requires a supply voltage of 5V. 3input lines are available for you to choose from.
SN74AHCT374DGVR Features
Cut Tape (CT) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT374DGVR Applications
There are a lot of Texas Instruments SN74AHCT374DGVR Flip Flops applications.
- Bounce elimination switch
- Data transfer
- Set-reset capability
- Individual Asynchronous Resets
- Latch
- Single Up Count-Control Line
- ESCC
- Balanced Propagation Delays
- Frequency Divider circuits
- Memory
