SN74AHCT374DGVRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 60.186038mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74AHCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT374DGVRE4 Overview
It is packaged in the way of 20-TFSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tape & Reel (TR) package. There is a Tri-State, Non-Invertedoutput configured with it. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. A temperature of -40°C~85°C TAis considered to be the operating temperature. This logic flip flop is classified as type D-Type. The 74AHCTseries comprises this type of FPGA. A frequency of 130MHzshould be the maximum output frequency. A total of 1elements are present in it. There is 4μA quiescent consumption. It has been determined that there have been 20 terminations. The object belongs to the 74AHCT374 family. A voltage of 5V is used as the power supply for this D latch. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In terms of electronic devices, this device belongs to the AHCT/VHCT/VTfamily of devices. This electronic part is mounted in the way of Surface Mount. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Considering its reliability, this T flip flop is well suited for TR. A total of 5V power supplies are needed to run it. A total of 2ports are embedded in the D flip flop. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It has 3lines.
SN74AHCT374DGVRE4 Features
Tape & Reel (TR) package
74AHCT series
20 pins
5V power supplies
SN74AHCT374DGVRE4 Applications
There are a lot of Texas Instruments SN74AHCT374DGVRE4 Flip Flops applications.
- Common Clocks
- Bounce elimination switch
- Divide a clock signal by 2 or 4
- Computers
- Single Up Count-Control Line
- Safety Clamp
- Count Modes
- Asynchronous counter
- Single Down Count-Control Line
- Load Control
