SN74AHCT574DBRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 115MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHCT574DBRG4 Overview
It is embeded in SSOP case. D flip flop is included in the Tape & Reel (TR)package. A total of 1elements are present in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. An input voltage of 5Vpowers the D latch. This D flip flop belongs to the family of AHCT/VHCT/VT. It is mounted by the way of Surface Mount. The 20pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. The RS flip flops belongs to FF/Latches base part number. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. The D flip flop has no ports embedded. In order to ensure high efficiency, the supply voltage should remain at 5V. Additionally, you may refer to the D latch's additional BROADSIDE VERSION OF 374. A -8mAvalue is set for the high level output current. In the low level output current setting, the current is set to 8mA. A temperature below 125°Cis recommended for operation. It is recommended that the operating temperature is higher than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis the maximum supply voltage supported by it. 115MHzis the maximum frequency that can be achieved. In this case, it uses a BUS DRIVER logic IC. Currently, it is equipped with 1 functions . With 20 pins, it is equipped with a low power consumption.
SN74AHCT574DBRG4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
SN74AHCT574DBRG4 Applications
There are a lot of Texas Instruments SN74AHCT574DBRG4 Flip Flops applications.
- Frequency Divider circuits
- Set-reset capability
- ESD performance
- Memory
- Synchronous counter
- Convert a momentary switch to a toggle switch
- CMOS Process
- Communications
- Instrumentation
- Consumer
