SN74AHCT574DW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceiver |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT574DW Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. D flip flop is included in the Tubepackage. As configured, the output uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. Surface Mountmounts this electrical part. The supply voltage is set to 4.5V~5.5V. Temperature is set to -40°C~85°C TA. A flip flop of this type is classified as a D-Type. It is a type of FPGA belonging to the 74AHCT series. There should be no greater frequency than 115MHzon its output. A total of 1elements are contained within it. There is a consumption of 4μAof quiescent energy. It has been determined that there have been 20 terminations. D latch belongs to the 74AHCT574 family. A voltage of 5V provides power to the D latch. Input capacitance of this device is 3pF farads. It is a member of the AHCT/VHCT/VTfamily of D flip flop. Electronic part Surface Mountis mounted in the way. The 20pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. This device is part of the Bus Driver/Transceiverbase part number family. Flip flops designed with 8bits are used in this part. There are 5V power supplies attached to it. The D flip flop has no ports embedded. The supply voltage should be maintained at 5V for high efficiency. With an output current of 8mA, this device offers maximum design flexibility. Currently, there are 3 lines of input. 8 channels are available.
SN74AHCT574DW Features
Tube package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT574DW Applications
There are a lot of Texas Instruments SN74AHCT574DW Flip Flops applications.
- Reduced system switching noise
- Digital electronics systems
- Patented noise
- Shift Registers
- Asynchronous counter
- Bus hold
- Computers
- Guaranteed simultaneous switching noise level
- Dynamic threshold performance
- Frequency division
