SN74AHCT574DWG4
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 115MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
SN74AHCT574DWG4 Overview
In the form of SOIC, it has been packaged. The list contains 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. A voltage of 5V is used to power it. This D flip flop belongs to the family of AHCT/VHCT/VT. The electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. The clock edge trigger type for this device is Positive Edge. It is part of the FF/Latchesbase part number family. In view of its reliability, this D flip flop is a good fit for TUBE. The D latch operates on 5V volts. The D flip flop is embedded with 2ports. For high efficiency, the supply voltage should be set to 5V. Additionally, there are BROADSIDE VERSION OF 374 on the electronic flip flop that can be referred to. It is set to -8mAfor the high level output current. In the low level output current setting, the current is set to 8mA. There should be a temperature below 125°Cduring operation. Ideally, the operating temperature should be higher than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis the maximum supply voltage it supports. This can be achieved at a frequency of 115MHz. BUS DRIVERis the logic IC it uses. There are 1 functions available on this T flip flop. The D latch is equipped with 20 pins.
SN74AHCT574DWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74AHCT574DWG4 Applications
There are a lot of Texas Instruments SN74AHCT574DWG4 Flip Flops applications.
- Frequency division
- Registers
- Buffered Clock
- ESCC
- Shift Registers
- Supports Live Insertion
- Bus hold
- Shift registers
- Reduced system switching noise
- Latch
