SN74AHCT574DWRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 115MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | AUTOMOTIVE |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHCT574DWRE4 Overview
The flip flop is packaged in a case of SOIC. The Tape & Reel (TR)package contains it. Terminations are 20. Power is supplied from a voltage of 5V volts. The electronic device belongs to the AHCT/VHCT/VTfamily. This electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device has Positive Edgeas its clock edge trigger type. This RS flip flops is a part number FF/Latches. The design is based on 8bits. To achieve this superior flexibility, 8 circuits are used. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. In order for the device to operate, it requires 5V power supplies. There are 2 ports embedded in the flip flops. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. There are 1 output lines on it. A total of 3input lines have been provided. A -8mAis set for the high level output current. It is set to 8mAfor low level output current. Ideally, the operating temperature should be lower than 125°C. In order for the system to operate properly, the temperature should be higher than -40°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum supply voltage of 5.5V. This frequency can be achieved 115MHz. In this case, it uses a BUS DRIVER logic IC. It has 1 functions. The JK flip flop has a pin count of 20.
SN74AHCT574DWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74AHCT574DWRE4 Applications
There are a lot of Texas Instruments SN74AHCT574DWRE4 Flip Flops applications.
- Parallel data storage
- Synchronous counter
- Bounce elimination switch
- Control circuits
- Common Clocks
- Reduced system switching noise
- Bus hold
- Matched Rise and Fall
- Frequency division
- Computing
