SN74AHCT574NSR
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
SN74AHCT574NSR Overview
20-SOIC (0.209, 5.30mm Width)is the way it is packaged. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Tri-State, Non-Invertedas the output. This trigger uses the value Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. A temperature of -40°C~85°C TAis used in the operation. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74AHCTseries FPGA. It should not exceed 115MHzin its output frequency. D latch consists of 1 elements. It consumes 4μA of quiescent A total of 20 terminations have been made. It is a member of the 74AHCT574 family. A voltage of 5V is used as the power supply for this D latch. A 3pFfarad input capacitance is provided by this T flip flop. Devices in the AHCT/VHCT/VTfamily are electronic devices. It is mounted by the way of Surface Mount. There are 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device has the base part number FF/Latches. The flip flop is designed with 8bits. Despite its superior flexibility, it relies on 8 circuits to achieve it. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. The power supply is 5V. This D flip flop is equipped with 0 ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It is reported that there are 3 input lines.
SN74AHCT574NSR Features
Tape & Reel (TR) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT574NSR Applications
There are a lot of Texas Instruments SN74AHCT574NSR Flip Flops applications.
- Data storage
- Asynchronous counter
- Bounce elimination switch
- Data Synchronizers
- Guaranteed simultaneous switching noise level
- Control circuits
- Frequency division
- Individual Asynchronous Resets
- Clock pulse
- Convert a momentary switch to a toggle switch
