SN74AHCT574PWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 10.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT574PWRG4 Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with the trigger Positive Edge. The electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. A temperature of -40°C~125°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74AHCTseries FPGA. Its output frequency should not exceed 115MHz Hz. There are 1 elements in it. It consumes 4μA of quiescent A total of 20 terminations have been made. If you search by 74AHCT574, you will find similar parts. An input voltage of 5Vpowers the D latch. This T flip flop has a capacitance of 3pF farads at the input. Devices in the AHCT/VHCT/VTfamily are electronic devices. In this case, the electronic component is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. The clock edge trigger type for this device is Positive Edge. It is included in FF/Latches. The design is based on 8bits. The superior flexibility is achieved through the use of 8 circuits. Due to its reliability, this T flip flop is well suited for TR. An electrical current of 5V volts is applied to it. There are 2 ports embedded in the flip flops. For high efficiency, the supply voltage should be set to 5V. It is reported that there are 3 input lines.
SN74AHCT574PWRG4 Features
Tape & Reel (TR) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT574PWRG4 Applications
There are a lot of Texas Instruments SN74AHCT574PWRG4 Flip Flops applications.
- ESCC
- Dynamic threshold performance
- Data transfer
- Power down protection
- Computing
- Safety Clamp
- Computers
- Test & Measurement
- Bounce elimination switch
- Convert a momentary switch to a toggle switch
