SN74AHCT74DR
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 13 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 4 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 65000000Hz |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT74DR Overview
It is packaged in the way of 14-SOIC (0.154, 3.90mm Width). A package named Cut Tape (CT)includes it. There is a Differentialoutput configured with it. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. With a supply voltage of 4.5V~5.5V volts, it operates. It is operating at -40°C~125°C TA. This D latch has the type D-Type. It belongs to the 74AHCTseries of FPGAs. It should not exceed 140MHzin terms of its output frequency. In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is a member of the 74AHCT74 family. A voltage of 5V provides power to the D latch. The input capacitance of this T flip flop is 2pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the AHCT/VHCT/VTfamily. There is an electronic part that is mounted in the way of Surface Mount. The 14pins are designed into the board. This device has the clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. Due to its superior flexibility, it uses 2 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. A total of 5V power supplies are needed to run it. In order to achieve high efficiency, the supply voltage should be maintained at 5V. Currently, there are 4 input lines present. It consumes 2μA current.
SN74AHCT74DR Features
Cut Tape (CT) package
74AHCT series
14 pins
5V power supplies
SN74AHCT74DR Applications
There are a lot of Texas Instruments SN74AHCT74DR Flip Flops applications.
- Single Up Count-Control Line
- High Performance Logic for test systems
- Automotive
- Count Modes
- Consumer
- Latch
- Reduced system switching noise
- Memory
- Set-reset capability
- Circuit Design
