SN74AHCT74PWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 8.8 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 4 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 65000000Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT74PWG4 Overview
The flip flop is packaged in 14-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tube package. It is configured with Differentialas an output. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. With a supply voltage of 4.5V~5.5V volts, it operates. Temperature is set to -40°C~125°C TA. This D latch has the type D-Type. FPGAs belonging to the 74AHCTseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 140MHz. During its operation, it consumes 2μA quiescent energy. It has been determined that there have been 14 terminations. D latch belongs to the 74AHCT74 family. The power supply voltage is 5V. Its input capacitance is 2pFfarads. In this case, the D flip flop belongs to the AHCT/VHCT/VTfamily. The electronic part is mounted in the way of Surface Mount. This board has 14 pins. In this device, the clock edge trigger type is Positive Edge. It is included in FF/Latches. The superior flexibility is achieved through the use of 2 circuits. It runs on 5Vvolts of power. High efficiency requires the supply voltage to be maintained at 5V. Currently, there are 4 lines of input.
SN74AHCT74PWG4 Features
Tube package
74AHCT series
14 pins
5V power supplies
SN74AHCT74PWG4 Applications
There are a lot of Texas Instruments SN74AHCT74PWG4 Flip Flops applications.
- Bus hold
- Test & Measurement
- CMOS Process
- Functionally equivalent to the MC10/100EL29
- Storage Registers
- Frequency Dividers
- Common Clocks
- Power down protection
- Computing
- ESCC
