SN74AHCT74PWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latch |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 8.8 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 4 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 65000000Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT74PWRG4 Overview
The flip flop is packaged in 14-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop uses Differentialas the output. JK flip flop uses Positive Edgeas the trigger. In this case, the electronic component is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. Currently, the operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. In this case, it is a type of FPGA belonging to the 74AHCT series. Its output frequency should not exceed 140MHz. As a result, it consumes 2μA of quiescent current without being affected by external factors. The number of terminations is 14. JK flip flop belongs to 74AHCT74 family. It is powered by a voltage of 5V . The input capacitance of this JK flip flopis 2pF farads. In terms of electronic devices, this device belongs to the AHCT/VHCT/VTfamily of devices. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 14. This device exhibits a clock edge trigger type of Positive Edge. There is a base part number FF/Latchfor the RS flip flops. The superior flexibility is achieved through the use of 2 circuits. A reliable performance of this D flip flop makes it well suited for use in TR. The D latch runs on a voltage of 5V volts. Optimal efficiency requires a supply voltage of 5V. This input has 4lines in it.
SN74AHCT74PWRG4 Features
Tape & Reel (TR) package
74AHCT series
14 pins
5V power supplies
SN74AHCT74PWRG4 Applications
There are a lot of Texas Instruments SN74AHCT74PWRG4 Flip Flops applications.
- Bus hold
- Parallel data storage
- Registers
- Buffered Clock
- QML qualified product
- Set-reset capability
- Memory
- EMI reduction circuitry
- 2 – Bit synchronous counter
- Synchronous counter
