SN74ALS109AD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | JK Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS109 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Output Current | 8mA |
| Clock Frequency | 34MHz |
| Propagation Delay | 18 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4mA |
| Current - Output High, Low | 400μA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 18ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 4mA |
| Number of Input Lines | 5 |
| fmax-Min | 34 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 34000000Hz |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS109AD Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. D flip flop is embedded in the Tube package. There is a Differentialoutput configured with it. This trigger is configured to use Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 4.5V~5.5Vis used as the supply voltage. In this case, the operating temperature is 0°C~70°C TA. The type of this D latch is JK Type. In FPGA terms, D flip flop is a type of 74ALSseries FPGA. There should be no greater frequency than 34MHzon its output. As a result, it consumes 4mA of quiescent current without being affected by external factors. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on 74ALS109. It is powered by a voltage of 5V . It is a member of the ALSfamily of D flip flop. Electronic part Surface Mountis mounted in the way. This board is designed with 16pins on it. This device exhibits a clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. 2 circuits are used to achieve its superior flexibility. The D latch runs on a voltage of 5V volts. For high efficiency, the supply voltage should be set to 5V. With an output current of 8mA, this device offers maximum design flexibility. It has 5lines.
SN74ALS109AD Features
Tube package
74ALS series
16 pins
5V power supplies
SN74ALS109AD Applications
There are a lot of Texas Instruments SN74ALS109AD Flip Flops applications.
- Balanced 24 mA output drivers
- Power down protection
- Safety Clamp
- Count Modes
- Memory
- Frequency Dividers
- Load Control
- High Performance Logic for test systems
- Shift registers
- Functionally equivalent to the MC10/100EL29
