SN74ALS109AN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Type | JK Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74ALS109 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Max Output Current | 8mA |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Nominal Supply Current | 11.5mA |
| Output Current | 8mA |
| Clock Frequency | 34MHz |
| Propagation Delay | 18 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4mA |
| Current - Output High, Low | 400μA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 18ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 4mA |
| Number of Input Lines | 5 |
| fmax-Min | 34 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 34000000Hz |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS109AN Overview
The package is in the form of 16-DIP (0.300, 7.62mm). D flip flop is embedded in the Tube package. As configured, the output uses Differential. JK flip flop uses Positive Edgeas the trigger. There is an electrical part that is mounted in the way of Through Hole. A voltage of 4.5V~5.5Vis used as the supply voltage. A temperature of 0°C~70°C TAis considered to be the operating temperature. JK Typeis the type of this D latch. In this case, it is a type of FPGA belonging to the 74ALS series. This D flip flop should not have a frequency greater than 34MHz. It consumes 4mA of quiescent There are 16 terminations,The 74ALS109family includes it. An input voltage of 5Vpowers the D latch. An electronic device belonging to the family ALScan be found here. There is an electronic part that is mounted in the way of Through Hole. This board is designed with 16pins on it. This device has Positive Edgeas its clock edge trigger type. This device is part of the FF/Latchesbase part number family. Using 2 circuits, it is highly flexible. There are 5V power supplies attached to it. In order to achieve high efficiency, the supply voltage should be maintained at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 8mA. Currently, there are 5 lines of input.
SN74ALS109AN Features
Tube package
74ALS series
16 pins
5V power supplies
SN74ALS109AN Applications
There are a lot of Texas Instruments SN74ALS109AN Flip Flops applications.
- Buffer registers
- Set-reset capability
- Synchronous counter
- Shift Registers
- Frequency division
- Circuit Design
- Differential Individual
- Control circuits
- Bounce elimination switch
- Power down protection
