SN74ALS174D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Clock Frequency | 50MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 19mA |
| Current - Output High, Low | 400μA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Number of Output Lines | 2 |
| fmax-Min | 50 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 50000000Hz |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS174D Overview
The flip flop is packaged in 16-SOIC (0.154, 3.90mm Width). There is an embedded version in the package Tube. Currently, the output is configured to use Non-Inverted. The trigger configured with it uses Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. Temperature is set to 0°C~70°C TA. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74ALS series. There should be no greater frequency than 50MHzon its output. D latch consists of 1 elements. There is a consumption of 19mAof quiescent energy. A total of 16terminations have been recorded. The 74ALS174 family contains it. Power is supplied from a voltage of 5V volts. An electronic device belonging to the family ALScan be found here. Electronic part Surface Mountis mounted in the way. With its 16pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. To achieve this superior flexibility, 7 circuits are used. A power supply of 5Vis required to operate it. In order to achieve high efficiency, the supply voltage should be maintained at 5V. With an output current of 8mA, it is possible to design the device in any way you want. It is designed with 2 output lines. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply.
SN74ALS174D Features
Tube package
74ALS series
16 pins
5V power supplies
SN74ALS174D Applications
There are a lot of Texas Instruments SN74ALS174D Flip Flops applications.
- Balanced 24 mA output drivers
- Memory
- Buffer registers
- Control circuits
- CMOS Process
- Registers
- Differential Individual
- Frequency Dividers
- Computers
- Safety Clamp
