SN74ALS174DG4
| Parameters | |
|---|---|
| Current - Output High, Low | 400μA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Number of Output Lines | 2 |
| fmax-Min | 50 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 50000000Hz |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Clock Frequency | 50MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 19mA |
SN74ALS174DG4 Overview
As a result, it is packaged as 16-SOIC (0.154, 3.90mm Width). As part of the package Tube, it is embedded. T flip flop uses Non-Invertedas its output configuration. There is a trigger configured with Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of 0°C~70°C TAis used in the operation. There is D-Type type of electronic flip flop associated with this device. This type of FPGA is a part of the 74ALS series. It should not exceed 50MHzin its output frequency. In total, it contains 1 elements. As a result, it consumes 19mA quiescent current. A total of 16terminations have been recorded. The 74ALS174 family contains this object. Power is supplied from a voltage of 5V volts. Devices in the ALSfamily are electronic devices. Surface Mount mounts this electronic component. As you can see from the design, it has pins with 16. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. In order to achieve its superior flexibility, 7 circuits are used. The power supply is 5V. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. As a result of its output current of 8mA, it is very flexible in terms of design. The JK flip flop is with 2 output lines to operate. Currently, there are 3 input lines present.
SN74ALS174DG4 Features
Tube package
74ALS series
16 pins
5V power supplies
SN74ALS174DG4 Applications
There are a lot of Texas Instruments SN74ALS174DG4 Flip Flops applications.
- Patented noise
- Latch-up performance
- Synchronous counter
- Test & Measurement
- Frequency Divider circuits
- Frequency division
- ESD protection
- Asynchronous counter
- Storage registers
- Divide a clock signal by 2 or 4
