SN74ALS374ADWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 35MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 16 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| High Level Output Current | -2.6mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74ALS374ADWRG4 Overview
The flip flop is packaged in SOIC. It is contained within the Tape & Reel (TR)package. Currently, the output is configured to use TTL. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is powered by a voltage of 5V . Electronic devices of this type belong to the ALSfamily. This electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. There are 8bits in this flip flop. Its superior flexibility is attributed to its use of 8 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It operates from 5V power supplies. This D flip flop is equipped with 0 ports. The supply voltage should be maintained at 5V for high efficiency. The JK flip flop is with 1 output lines to operate. Currently, there are 3 lines of input. A -2.6mAvalue is set for the high level output current. The low level output current is set to 24mA. A temperature below 70°Cshould be used for operation. If the operating temperature is higher than 0°C, the system should operate properly. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis its maximum supply voltage. It is possible to achieve a frequency of 35MHz. In this case, it uses a BUS DRIVER logic IC. It has 1 functions. It is equipped with 20 pins. In addition to its maximum design flexibility, the output current of the flip flop is 24mA.
SN74ALS374ADWRG4 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74ALS374ADWRG4 Applications
There are a lot of Texas Instruments SN74ALS374ADWRG4 Flip Flops applications.
- Set-reset capability
- Functionally equivalent to the MC10/100EL29
- 2 – Bit synchronous counter
- Balanced Propagation Delays
- Computing
- Circuit Design
- Pattern generators
- CMOS Process
- ESD performance
- Latch
