SN74ALS564BDW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS564 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 18mA |
| Current - Output High, Low | 2.6mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 14ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS564BDW Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). It is contained within the Tubepackage. As configured, the output uses Tri-State, Inverted. In the configuration of the trigger, Positive Edgeis used. The electronic part is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. A temperature of 0°C~70°C TAis considered to be the operating temperature. This electronic flip flop is of type D-Type. It is a type of FPGA belonging to the 74ALS series. There should be no greater frequency than 30MHzon its output. There are 1 elements in it. As a result, it consumes 18mA quiescent current and is not affected by external forces. 20terminations have occurred. D latch belongs to the 74ALS564 family. Power is supplied from a voltage of 5V volts. This D flip flop belongs to the family of ALS. The electronic part is mounted in the way of Surface Mount. The 20pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. This flip flop is designed with 8 Bits. Due to its superior flexibility, it uses 8 circuits. The D latch runs on a voltage of 5V volts. A total of 2ports are embedded in the D flip flop. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. This T flip flop features a maximum design flexibility due to its output current of 24mA. It has 3lines.
SN74ALS564BDW Features
Tube package
74ALS series
20 pins
8 Bits
5V power supplies
SN74ALS564BDW Applications
There are a lot of Texas Instruments SN74ALS564BDW Flip Flops applications.
- Reduced system switching noise
- EMI reduction circuitry
- Consumer
- Computers
- 2 – Bit synchronous counter
- Control circuits
- Matched Rise and Fall
- Count Modes
- ESCC
- Patented noise
