SN74ALS574BDWG4
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 35MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -2.6mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
SN74ALS574BDWG4 Overview
SOICis the way it is packaged. Currently, the output is configured to use TTL. A total of 1 elements are present. Currently, there are 20 terminations. The power supply voltage is 5V. It is a member of the ALSfamily of D flip flop. There is an electronic component mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device has Positive Edgeas its clock edge trigger type. This device is part of the FF/Latchesbase part number family. Considering its reliability, this T flip flop is well suited for TUBE. The D latch operates on 5V volts. The flip flop has 2ports embedded within it. In order to ensure high efficiency, the supply voltage should remain at 5V. Furthermore, it has BROADSIDE VERSION OF 374as a characteristic. High level output current is set to -2.6mA. 24mAis set as the low level output current. A temperature below 70°Cis recommended for operation. In order for the system to operate properly, the temperature should be higher than 0°C. The minimum voltage required for operation is 4.5V. It supports a maximum supply voltage of 5.5V volts. 35MHzis the maximum frequency that can be achieved. It uses the logic IC BUS DRIVER. It has 1 functions. 20pins are available on this JK flip flop. It offers maximum design flexibility with its output current of 24mA.
SN74ALS574BDWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74ALS574BDWG4 Applications
There are a lot of Texas Instruments SN74ALS574BDWG4 Flip Flops applications.
- Computing
- Circuit Design
- Divide a clock signal by 2 or 4
- Count Modes
- Modulo – n – counter
- Buffered Clock
- Individual Asynchronous Resets
- Set-reset capability
- Instrumentation
- Consumer
