SN74ALS574BDWRG4
| Parameters | |
|---|---|
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 35MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 3 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | 24mA |
| Low Level Output Current | 2.6mA |
| Control Type | ENABLE LOW |
| Power Supply Current-Max (ICC) | 30mA |
| Count Direction | UNIDIRECTIONAL |
SN74ALS574BDWRG4 Overview
As a result, it is packaged as SOIC. You can find it in the Tape & Reel (TR)package. The output it is configured with uses TTL. A total of 1elements are contained within it. It has been determined that there have been 20 terminations. Power is supplied from a voltage of 5V volts. It belongs to the family of electronic devices known as ALS. This electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device exhibits a clock edge trigger type of Positive Edge. It is included in FF/Latches. A reliable performance of this D flip flop makes it well suited for use in TR. In order for the device to operate, it requires 5V power supplies. The flip flop has 2embedded ports. High efficiency requires the supply voltage to be maintained at 5V. Additionally, there are BROADSIDE VERSION OF 374 on the electronic flip flop that can be referred to. In this case, the high level output current is set to 24mA. There is no low level output current set at 2.6mA. Ideally, the operating temperature should be below 70°C. The operating temperature should be higher than 0°C. The system operates with a minimum supply voltage of 4.5V. 5.5Vis the maximum supply voltage it supports. This can be achieved at a frequency of 35MHz. BUS DRIVERis used as the logic IC in this D flip flop. As a result, it is equipped with 1 functions . The D latch is equipped with 20 pins. This flip flop features a maximum design flexibility due to its output current of 24mA.
SN74ALS574BDWRG4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
SN74ALS574BDWRG4 Applications
There are a lot of Texas Instruments SN74ALS574BDWRG4 Flip Flops applications.
- 2 – Bit synchronous counter
- Digital electronics systems
- Bus hold
- Buffer registers
- Computing
- QML qualified product
- Data transfer
- Test & Measurement
- Common Clocks
- Circuit Design
