SN74ALS575ADW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS575 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 4 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 17mA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 2.6mA 24mA |
| Max Propagation Delay @ V, Max CL | 14ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 30mA |
| Number of Input Lines | 4 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS575ADW Overview
The package is in the form of 24-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tube package. T flip flop is configured with an output of Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. It operates with a supply voltage of 4.5V~5.5V. Temperature is set to 0°C~70°C TA. A flip flop of this type is classified as a D-Type. In terms of FPGAs, it belongs to the 74ALS series. In order for it to function properly, its output frequency should not exceed 30MHz. A total of 1elements are present in it. As a result, it consumes 17mA quiescent current. A total of 24 terminations have been made. The 74ALS575family includes it. An input voltage of 5Vpowers the D latch. This D flip flop belongs to the family of ALS. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 24. This device has the clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part designed with 8bits is used in this application. Despite its superior flexibility, it relies on 8 circuits to achieve it. There are 5V power supplies attached to it. There are 2 ports embedded in the flip flops. High efficiency requires the supply voltage to be maintained at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. This input has 4lines.
SN74ALS575ADW Features
Tube package
74ALS series
24 pins
8 Bits
5V power supplies
SN74ALS575ADW Applications
There are a lot of Texas Instruments SN74ALS575ADW Flip Flops applications.
- Data transfer
- Divide a clock signal by 2 or 4
- Computing
- Balanced Propagation Delays
- Bus hold
- Modulo – n – counter
- Supports Live Insertion
- Computers
- Count Modes
- Frequency Dividers
