SN74ALS666DWE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH CLEAR AND PRESET; WITH DUAL OUTPUT ENABLE; WITH READ-BACK |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ALS666 |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Output Type | Tri-State |
| Operating Supply Voltage | 5V |
| Circuit | 8:8 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Nominal Supply Current | 73mA |
| Output Current | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 18 ns |
| Turn On Delay Time | 6 ns |
| Family | ALS |
| Logic Function | D-Type, Latch |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 400μA 8mA |
| Logic Type | D-Type Transparent Latch |
| Control Type | ENABLE LOW/HIGH |
| Number of Input Lines | 8 |
| Independent Circuits | 1 |
| Count Direction | UNIDIRECTIONAL |
| Translation | N/A |
| Height | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS666DWE4 Overview
In the 24-SOIC (0.295, 7.50mm Width) package, it is embedded. Tube is the way it is packaged. In this configuration, the output is set to Tri-State. This electrical device has Logic type D-Type Transparent Latch. Mounting this electronic component follows the Surface Mount method. A 4.5V~5.5V voltage supply is required for operation. It is 0°C~70°C at the operating temperature. It is a type of FPGA belonging to the 74ALS series. An electronic part with 8 bits is designed. This device has been designed with 24 terminations available. There is no doubt that it belongs to the family 74ALS666. In order to operate it, the supply voltage must be 5V. 24 pins are included. ALS is the family of this electronic device. The pin configuration of the device is 24. The electronic part is mounted in a way that corresponds to Surface Mount. This device has a total of 2 ports. The part belongs to the FF/Latches subcategory. A total of 5V power supplies are needed to run it. It contains 8 input lines where electronic circuits are present. Its 24mA output current allows for maximum design flexibility. A high level of efficiency is achieved by maintaining the supply voltage at 5V. It also has characteristics of WITH CLEAR AND PRESET; WITH DUAL OUTPUT ENABLE; WITH READ-BACK.
SN74ALS666DWE4 Features
24-SOIC (0.295, 7.50mm Width) package
74ALS series
8 Bits
74ALS666 family
24 pin count
24 pins
5V power supplies
SN74ALS666DWE4 Applications
There are a lot of Texas Instruments SN74ALS666DWE4 Latches applications.
- Synchronous frequency dividers
- Timers
- Pattern Generators
- Parallel Input
- Parallel Input
- Automotive Cluster
- Sample and hold register
- Hammer Device Information
- Decade counting 7-segment decimal display
- Address register
