SN74AS374NSR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AS |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AS374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Number of Ports | 2 |
| Output Current | 48mA |
| Number of Bits | 8 |
| Clock Frequency | 125MHz |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 3 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 120mA |
| Current - Output High, Low | 15mA 48mA |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74AS374NSR Overview
As a result, it is packaged as 20-SOIC (0.209, 5.30mm Width). Package Tape & Reel (TR)embeds it. Tri-State, Non-Invertedis the output configured for it. This trigger is configured to use Positive Edge. Surface Mountis positioned in the way of this electronic part. It operates with a supply voltage of 4.5V~5.5V. A temperature of 0°C~70°C TAis considered to be the operating temperature. The type of this D latch is D-Type. It belongs to the 74ASseries of FPGAs. This D flip flop should not have a frequency greater than 125MHz. D latch consists of 1 elements. It consumes 120mA of quiescent In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is a member of the 74AS374 family. A voltage of 5V is used as the power supply for this D latch. The electronic device belongs to the ASfamily. Surface Mount mounts this electronic component. 20pins are included in its design. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Flip flops designed with 8bits are used in this part. The superior flexibility of this circuit is achieved by using 8 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. The flip flop has 2embedded ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 48mA. Currently, there are 3 input lines present.
SN74AS374NSR Features
Tape & Reel (TR) package
74AS series
20 pins
8 Bits
5V power supplies
SN74AS374NSR Applications
There are a lot of Texas Instruments SN74AS374NSR Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Digital electronics systems
- Storage Registers
- Registers
- Frequency Divider circuits
- 2 – Bit synchronous counter
- Modulo – n – counter
- Bus hold
- Functionally equivalent to the MC10/100EL29
- Synchronous counter
