SN74AS876DWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AS |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Additional Feature | WITH PRESET |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AS876 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Number of Elements | 2 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Ports | 2 |
| Number of Bits | 4 |
| Clock Frequency | 80MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 3 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 142mA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 15mA 48mA |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
SN74AS876DWRG4 Overview
The flip flop is packaged in a case of 24-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Tri-State, Invertedas its output configuration. The trigger configured with it uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. A temperature of 0°C~70°C TAis used in the operation. The type of this D latch is D-Type. The 74ASseries comprises this type of FPGA. You should not exceed 80MHzin the output frequency of the device. In total, it contains 2 elements. As a result, it consumes 142mA quiescent current. Terminations are 24. If you search by 74AS876, you will find similar parts. A voltage of 5V provides power to the D latch. This D flip flop belongs to the family of AS. There is an electronic part that is mounted in the way of Surface Mount. Basically, it is designed with a set of 24 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. This flip flop is designed with 4 Bits. There is a 5.5Vmaximum supply voltage (Vsup). In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is designed with 4 output lines. There is also a characteristic of WITH PRESET.
SN74AS876DWRG4 Features
Tape & Reel (TR) package
74AS series
24 pins
4 Bits
SN74AS876DWRG4 Applications
There are a lot of Texas Instruments SN74AS876DWRG4 Flip Flops applications.
- Synchronous counter
- Frequency division
- Latch
- ESCC
- Computing
- Single Down Count-Control Line
- Functionally equivalent to the MC10/100EL29
- Frequency Divider circuits
- Storage registers
- Bus hold
