SN74AUC1G66DCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.65V |
| Base Part Number | 74AUC1G66 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 2.7V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 100 ps |
| Turn On Delay Time | 2.2 ns |
| Supply Type | Single |
| Bandwidth | 170MHz |
| Turn-Off Delay Time | 1.4 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 15Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1.4ns, 1.5ns |
| Switch-off Time-Max | 2.9ns |
| Voltage - Supply, Single (V+) | 0.8V~2.7V |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AUC1G66DCKR Overview
Packed in 5-TSSOP, SC-70-5, SOT-353, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Cut Tape (CT). Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. 5 terminations have been made so far. A 1 channel electronic part produces high-quality output. A 1.65V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 5 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Search with 74AUC1G66 if you are looking for analog multiplexer variants. Analog switches have 15Ohm internal resistance. Please refer to the datasheets for 5 pins functions. Users shouldn't supply more than 2.7V voltage to the switch device. Digital switch that provides Single power at a cost-effective price. 800mV should be the lowest voltage fed to the electronic component. This multiplexer would work with 10μA current. The voltage required by this switch device is 0.8V~2.7V, draining from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 10μA. The transfer of data can be performed over 170MHz bandwidths.
SN74AUC1G66DCKR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 50MHz
Bandwidth: 170MHz
SN74AUC1G66DCKR Applications
There are a lot of Texas Instruments SN74AUC1G66DCKR Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Cellular phones
- Cross Connects
- Power routing
- Audio signal routing
- Industrial
- Sample-and-hold systems
- Isolation
- Cable Modem
- HDTV
