SN74AUC1G66DCKRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 15Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.65V |
| Base Part Number | 74AUC1G66 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 2.7V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 100 ps |
| Turn On Delay Time | 4.1 ns |
| Supply Type | Single |
| Bandwidth | 170MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 15Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1.4ns, 1.5ns |
| Switch-off Time-Max | 2.9ns |
| Voltage - Supply, Single (V+) | 0.8V~2.7V |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AUC1G66DCKRE4 Overview
As the electronic part is packed in 5-TSSOP, SC-70-5, SOT-353, international shipping is convenient. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~85°C TA are extended for operation. A total of 5 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. Turning on and running the electrical part should be easy with a 1.65V voltage supply. There is an electrical component included in the 5 series. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with 74AUC1G66 if you are looking for variants. There is 15Ohm internal resistance in this digital multiplexer. You can find the functions of the 5 pins in the datasheets. A voltage higher than 2.7V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 800mV. For this multiplexer to operate, 10μA current would be sufficient. A voltage of 0.8V~2.7V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 10μA on the multiplexer may cause damage. It is possible to transfer data over a 170MHz-bandwidth.
SN74AUC1G66DCKRE4 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 50MHz
Bandwidth: 170MHz
SN74AUC1G66DCKRE4 Applications
There are a lot of Texas Instruments SN74AUC1G66DCKRE4 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Audio and video routing
- Precision data acquisition
- SONET/SDH ADM
- DSLAMs
- Signal routing between systems
- PBX interfaces
- Imaging
- ATM
- Multi-Line E1 Interface Cards
