SN74AUC1G79YEPR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-XFBGA, DSBGA |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AUC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 0.8V~2.7V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 1.2V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AUC1G79 |
| JESD-30 Code | R-PBGA-B5 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 2.7V |
| Supply Voltage-Min (Vsup) | 0.8V |
| Number of Bits | 1 |
| Clock Frequency | 275MHz |
| Turn On Delay Time | 5 ns |
| Family | AUC |
| Current - Quiescent (Iq) | 10μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 9mA 9mA |
| Max I(ol) | 0.005 A |
| Max Propagation Delay @ V, Max CL | 1.8ns @ 2.5V, 30pF |
| Prop. Delay@Nom-Sup | 3.9 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Propagation Delay (tpd) | 3.9 ns |
| fmax-Min | 275 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 200000000Hz |
| Height Seated (Max) | 0.5mm |
| Width | 0.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74AUC1G79YEPR Overview
5-XFBGA, DSBGAis the packaging method. D flip flop is embedded in the Tape & Reel (TR) package. Non-Invertedis the output configured for it. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. A supply voltage of 0.8V~2.7V is required for operation. It is at -40°C~85°C TAdegrees Celsius that the system is operating. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 74AUCseries contain this type of chip. Its output frequency should not exceed 275MHz Hz. There are 1 elements in it. It consumes 10μA of quiescent In 5terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. You can search similar parts based on 74AUC1G79. The D flip flop is powered by a voltage of 1.2V . The input capacitance of this JK flip flopis 2.5pF farads. In terms of electronic devices, this device belongs to the AUCfamily of devices. This electronic part is mounted in the way of Surface Mount. It has a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. Flip flops designed with 1bits are used in this part. It reaches 2.7Vwhen the maximum supply voltage (Vsup) is applied. Normal operation requires a supply voltage (Vsup) above 0.8V. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL.
SN74AUC1G79YEPR Features
Tape & Reel (TR) package
74AUC series
1 Bits
SN74AUC1G79YEPR Applications
There are a lot of Texas Instruments SN74AUC1G79YEPR Flip Flops applications.
- Power down protection
- Reduced system switching noise
- Divide a clock signal by 2 or 4
- Frequency division
- Computing
- Convert a momentary switch to a toggle switch
- Memory
- Registers
- Common Clocks
- Shift Registers
