SN74AUP1G79DBVTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AUP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 0.8V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.2V |
| Base Part Number | 74AUP1G79 |
| Function | Standard |
| Output Type | Non-Inverted |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 0.8V |
| Number of Circuits | 1 |
| Load Capacitance | 30pF |
| Output Current | 4mA |
| Number of Bits | 1 |
| Clock Frequency | 266MHz |
| Propagation Delay | 17.3 ns |
| Turn On Delay Time | 3 ns |
| Family | AUP/ULP/V |
| Current - Quiescent (Iq) | 500nA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 5.8ns @ 3.3V, 30pF |
| Prop. Delay@Nom-Sup | 24 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.5pF |
| Power Supply Current-Max (ICC) | 0.0009mA |
| fmax-Min | 260 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 220000000Hz |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AUP1G79DBVTG4 Overview
The flip flop is packaged in a case of SC-74A, SOT-753. D flip flop is included in the Tape & Reel (TR)package. T flip flop uses Non-Invertedas its output configuration. There is a trigger configured with Positive Edge. There is an electric part mounted in the way of Surface Mount. Powered by a 0.8V~3.6Vvolt supply, it operates as follows. In the operating environment, the temperature is -40°C~85°C TA. D-Typeis the type of this D latch. JK flip flop is a part of the 74AUPseries of FPGAs. This D flip flop should not have a frequency greater than 266MHz. There is 500nA quiescent consumption. There have been 5 terminations. JK flip flop belongs to 74AUP1G79 family. The power supply voltage is 1.2V. Input capacitance of this device is 1.5pF farads. A device of this type belongs to the family of AUP/ULP/V. This electronic part is mounted in the way of Surface Mount. 5pins are included in its design. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. An electronic part with 1bits has been designed. The maximal supply voltage (Vsup) reaches 3.6V. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 0.8V. Using 1 circuits, it is highly flexible. In view of its reliability, this D flip flop is a good fit for TR. With an output current of 4mA, it is possible to design the device in any way you want.
SN74AUP1G79DBVTG4 Features
Tape & Reel (TR) package
74AUP series
5 pins
1 Bits
SN74AUP1G79DBVTG4 Applications
There are a lot of Texas Instruments SN74AUP1G79DBVTG4 Flip Flops applications.
- Data transfer
- Matched Rise and Fall
- Bounce elimination switch
- Shift Registers
- Single Up Count-Control Line
- Single Down Count-Control Line
- Automotive
- Guaranteed simultaneous switching noise level
- CMOS Process
- Modulo – n – counter
