SN74BCT374DWR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74BCT |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74BCT374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 70MHz |
| Propagation Delay | 9.1 ns |
| Turn On Delay Time | 7.2 ns |
| Family | BCT/FBT |
| Logic Function | D-Type, Latch |
| Current - Quiescent (Iq) | 5mA |
| Current - Output High, Low | 15mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 9.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 6pF |
| Power Supply Current-Max (ICC) | 60mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
SN74BCT374DWR Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). Package Tape & Reel (TR)embeds it. The output it is configured with uses Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. Currently, the operating temperature is 0°C~70°C TA. The type of this D latch is D-Type. It belongs to the 74BCTseries of FPGAs. You should not exceed 70MHzin the output frequency of the device. D latch consists of 1 elements. T flip flop consumes 5mA quiescent energy. Currently, there are 20 terminations. If you search by 74BCT374, you will find similar parts. A voltage of 5V provides power to the D latch. This T flip flop has a capacitance of 6pF farads at the input. BCT/FBTis the family of this D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. An electronic part designed with 8bits is used in this application. Vsup reaches 5.5V, the maximal supply voltage. Keeping the supply voltage (Vsup) above 4.5V is necessary for normal operation. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The D latch operates on 5V volts. This flip flop has a total of 2ports. In addition to its maximum design flexibility, the output current of the T flip flop is 64mA. There are 3 output lines on it. The number of input lines is 8.
SN74BCT374DWR Features
Tape & Reel (TR) package
74BCT series
20 pins
8 Bits
5V power supplies
SN74BCT374DWR Applications
There are a lot of Texas Instruments SN74BCT374DWR Flip Flops applications.
- Latch-up performance
- Dynamic threshold performance
- Load Control
- Count Modes
- Memory
- Balanced Propagation Delays
- Pattern generators
- Automotive
- ATE
- Buffered Clock
