SN74CB3Q3306APWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Weight | 39.008944mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74CB |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | Bus Switch |
| Resistance | 9Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceivers |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2.3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74CB3Q3306 |
| Pin Count | 8 |
| Circuit | 1 x 1:1 |
| Supply Voltage-Max (Vsup) | 3.6V |
| Number of Channels | 2 |
| Number of Ports | 2 |
| Nominal Supply Current | 250μA |
| Output Current | 30mA |
| Number of Bits | 1 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 700μA |
| Turn On Delay Time | 6.5 ns |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Bandwidth | 500MHz |
| Output Polarity | TRUE |
| High Level Output Current | -64mA |
| Low Level Output Current | 64mA |
| Voltage Supply Source | Single Supply |
| Count Direction | BIDIRECTIONAL |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74CB3Q3306APWRG4 Overview
In order to save board space, digital switch is located in the 8-TSSOP (0.173, 4.40mm Width).The package is in the form of Tape & Reel (TR).For mounting, digital switch ic uses the method Surface Mount.In the multiplexers, the analog IC Bus Switch is used.In the case of -40°C~85°C, turn signal switch will not be affected by external factors.Using a 2.3V~3.6V supply voltage provides digital controlled switch's superior flexibility for designers.The multiplexers from 74CB series can be used for a wide range of applications.There are 8 terminations included in its basic configuration.There is a base part number 74CB3Q3306 that can be used to locate signal switch's related components as well.The turn signal switch is supplied with a voltage of 2.5V volts.This turn signal switch consists of 8 component pins.As a result, conductors end at GULL WING.Single is used as its supply type.This multiplexer ic has 8 pins configured.The mount is in Surface Mount.Signal multiplexer contains 1 bits.It is advisable to keep the maximum supply voltage (Vsup) at 3.6V in order to prevent some unnecessary failures.The digital switch ic is an electronic part classified into Bus Driver/Transceivers.Without the influence of external factors, it consumes 700μA current of multiplexer ic.TR is used to package the switches.As far as the resistance is concerned, it operates with 2.With a resistance of 9Ohm, it operates.This turn signal switch's circuit is based on a circuit with 2 channels.For greater switches' flexibility, 30mA provides the output current.
SN74CB3Q3306APWRG4 Features
Supplied in the 8-TSSOP (0.173, 4.40mm Width) package
Adopting a supply type of Single
SN74CB3Q3306APWRG4 Applications
There are a lot of Texas Instruments SN74CB3Q3306APWRG4 Signal Switches / Multiplexers / Decoders applications.
- PCIe
- Electronic circuits
- Signal router
- Microprocessor memory systems
- Frequency multiplexing system
- RF-based home automation system
- Night vision cameras
- Code conversion
- Memory system of computers
- Encrypted communications system
