SN74CBT3861DGVR
| Parameters | |
|---|---|
| Type | Bus Switch |
| Resistance | 7Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74CBT3861 |
| Pin Count | 24 |
| Operating Supply Voltage | 5V |
| Circuit | 10 x 1:1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Ports | 2 |
| Nominal Supply Current | 3μA |
| Output Current | 64mA |
| Number of Bits | 10 |
| Throw Configuration | SPST |
| Propagation Delay | 250 ps |
| Quiescent Current | 3μA |
| Turn On Delay Time | 8.1 ns |
| Family | CBT/FST/QS/5C/B |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| High Level Output Current | -128mA |
| Low Level Output Current | 128mA |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 1 |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Weight | 60.894776mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | 74CBT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
SN74CBT3861DGVR Overview
Due to the fact that it is provided in the 24-TFSOP (0.173, 4.40mm Width), digital switch allows the board to be compacted.The package is in the form of Cut Tape (CT).As far as mounting is concerned, digital switch ic uses Surface Mount.In the multiplexers, the analog IC Bus Switch is used.By maintaining the operating temperature at -40°C~85°C, turn signal switch will not be affected by external factors.With a supply voltage of 4.5V~5.5V, designers have greater flexibility of digital controlled switch.The multiplexers from 74CBT series can be used for a wide range of applications.The basic configuration includes 24 terminations.As its base part number is 74CBT3861, logic switch can also be used to find its related parts.In this case, 5V is the voltage supplied to the multiplexer's system.This turn signal switch consists of 24 component pins.Using the point GULL WING as an end point of conductors, it is used to determine the terminus of a conductor.Its supply type is Single, which is used as the source of power.A configuration of 24 pins is used.The multiplexer ic is mounted in the direction of Surface Mount.There is a family of CBT/FST/QS/5C/B members.There are 10 bits in signal multiplexer.Avoid unnecessary failures by keeping the supply voltage (Vsup) at 4V.For mux switch's normal operation, power supply 5V is provided.This is a signal switch that is categorized as Bus Driver/Transceivers.Without the influence of external factors, it consumes 3μA current of multiplexer ic.It is possible to achieve reliable performance of the multiplexers with a voltage supply of 5V.A resistance of 2 is used to operate the signal switching.A resistance of 7Ohm is used to operate the signal switching.For higher switches' flexibility, the output current is set to 64mA.
SN74CBT3861DGVR Features
Supplied in the 24-TFSOP (0.173, 4.40mm Width) package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
SN74CBT3861DGVR Applications
There are a lot of Texas Instruments SN74CBT3861DGVR Signal Switches / Multiplexers / Decoders applications.
- Textile mills
- High-performance memory systems
- Communication system
- Code conversion
- Relay
- CNC machines
- Make full adder
- Analog, digital or video signal switching
- VGA
- Time division multiplexing system
