banner_page

SN74CBTD3306DG4

8 Terminations8 Pin Signal switch2 FunctionsMin 4.5V VMax 5.5V V


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-SN74CBTD3306DG4
  • Package: SOIC
  • Datasheet: -
  • Stock: 730
  • Description: 8 Terminations8 Pin Signal switch2 FunctionsMin 4.5V VMax 5.5V V(Kg)

Details

Tags

Parameters
Mount Surface Mount
Package / Case SOIC
Number of Pins 8
Weight 72.603129mg
JESD-609 Code e4
Moisture Sensitivity Level (MSL) 1
Number of Terminations 8
Resistance 7Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Additional Feature BUS SWITCH
Subcategory Bus Driver/Transceivers
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 5V
Pin Count 8
Operating Supply Voltage 5V
Power Supplies 5V
Temperature Grade INDUSTRIAL
Number of Channels 2
Max Supply Voltage 5.5V
Min Supply Voltage 4.5V
Load Capacitance 50pF
Number of Ports 2
Nominal Supply Current 1.5mA
Current - Output 64mA
Number of Bits 1
Propagation Delay 250 ps
Quiescent Current 1.5mA
Turn On Delay Time 5.4 ns
Family CBT/FST/QS/5C/B
Output Characteristics 3-STATE
Supply Type Single
Bandwidth 20MHz
Output Polarity TRUE
Logic IC Type BUS DRIVER
High Level Output Current -128mA
Low Level Output Current 128mA
Height 1.58mm
Length 4.9mm
Width 3.91mm
Radiation Hardening No
RoHS Status RoHS Compliant
Lead Free Lead Free

SN74CBTD3306DG4 Overview


Providing this information in the SOIC enables digital switch board space to be saved.It is designed with 8 terminations as part of its basic configuration.The turn signal switch is supplied with a voltage of 5V volts.This turn signal switch has 8 component pins.It employs GULL WING as the point at which conductors come to an end.In this case, the supply type is Single.Currently, it is configured with 8 pins.The mounting is in the way of Surface Mount.I would like to refer to the logic switch as a member of the CBT/FST/QS/5C/B family.In the signal multiplexer, there are 1 bits available.Normally, 5V is powered by a battery.The part belongs to the Bus Driver/Transceivers category of signal switches.No external influence consumes 1.5mA current of multiplexer ic.If the supply voltage is set to 5V, reliable performance of the multiplexers can be achieved.The resistance of the signal switching is 2.The system operates with a resistance of 7Ohm.The turn signal switch's circuit consists of 2 transmission channels.It is acceptable for this signal switch to operate at the maximal temperature of 85°C.In order to maintain a minimal operating temperature of the multiplexer, it should be set at -40°C.In compliance with the applicable device specification, the signal switches has a maximum supply voltage of 5.5V.A minimum supply voltage of 4.5V is required to operate the digital swith.In addition, BUS SWITCH exhibits improved characteristics.It uses IC BUS DRIVER for its logic.

SN74CBTD3306DG4 Features


Supplied in the SOIC package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
BUS SWITCH
BUS DRIVER as the logic IC

SN74CBTD3306DG4 Applications


There are a lot of Texas Instruments SN74CBTD3306DG4 Signal Switches / Multiplexers / Decoders applications.

  • Logic gates for other digital devices
  • Metal detectors
  • Idle motor
  • Enabling different rows of memory depending on address in memory chips
  • Audio transmission
  • Data collection system
  • Paper plants
  • Enabling different functions units in microprocessor instruction decoding
  • Automatic health monitoring systems
  • Data distribution

Write a review

Note: HTML is not translated!
    Bad           Good