SN74CBTR16861DGVR
| Parameters | |
|---|---|
| Supply Type | Single |
| High Level Output Current | -128mA |
| Low Level Output Current | 128mA |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 2 |
| Length | 9.7mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 48 |
| Weight | 123.490523mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | 74CBTR |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Type | Bus Switch |
| Resistance | 50Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74CBTR16861 |
| Pin Count | 48 |
| Operating Supply Voltage | 5V |
| Circuit | 10 x 1:1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Ports | 2 |
| Nominal Supply Current | 3μA |
| Output Current | 64mA |
| Number of Bits | 20 |
| Throw Configuration | SPST |
| Propagation Delay | 1.25 ns |
| Quiescent Current | 3μA |
| Turn On Delay Time | 9 ns |
| Family | CBT/FST/QS/5C/B |
| Output Characteristics | 3-STATE |
SN74CBTR16861DGVR Overview
As a means of saving space, digital switch is provided in the 48-TFSOP (0.173, 4.40mm Width).Cut Tape (CT) is the packaging method.Mounting is performed using Surface Mount.The multiplexers uses an analog IC Bus Switch as the analog part of the circuit.When the operating temperature is kept at -40°C~85°C, the machine will not be sensturn signal switchive to external influences.The turn signal switch is designed for use with a 4.5V~5.5V supply voltage, which gives it a lot of flexibility.Since they are members of the 74CBTR series, they can be used in a wide variety of applications.The basic configuration of this system includes 48 terminations.There is a base part number of 74CBTR16861 which can also be used in order to locate the logic switch that are related to this item.In this case, 5V is the voltage supplied to the multiplexer's system.Currently, this turn signal switch has a total of 48 component pins.It employs GULL WING as the point at which conductors come to an end.There is a type of supply of Single.The board has 48 pins configured.It is positioned in the direction of Surface Mount.I would like to refer to the logic switch as a member of the CBT/FST/QS/5C/B family.Signal multiplexer contains 20 bits.It is recommended that the minimum supply voltage (Vsup) be kept at 4V to avoid some unnecessary failures.During mux switch's normal operation, 5V is provided with a power supply.Part number Bus Driver/Transceivers indicates that the digital switch ic is an electronic part.No external influence consumes 3μA current of multiplexer ic.The performance of the multiplexers can be reliably maintained at a voltage of 5V.The system operates with a resistance of 2.It operates with a resistance of 50Ohm.64mA provides a high degree of switches' flexibility.
SN74CBTR16861DGVR Features
Supplied in the 48-TFSOP (0.173, 4.40mm Width) package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
SN74CBTR16861DGVR Applications
There are a lot of Texas Instruments SN74CBTR16861DGVR Signal Switches / Multiplexers / Decoders applications.
- CPU memory location identification
- Textile mills
- Data distribution
- Seven segment displays
- Code conversion
- Idle motor
- Make half adder
- Frequency multiplexing system
- LVDS
- Relay
