SN74CBTR16861DLR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | 74CBTR |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Type | Bus Switch |
| Resistance | 50Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74CBTR16861 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Circuit | 10 x 1:1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Ports | 2 |
| Nominal Supply Current | 3μA |
| Output Current | 64mA |
| Number of Bits | 20 |
| Throw Configuration | SPST |
| Propagation Delay | 1.25 ns |
| Quiescent Current | 3μA |
| Turn On Delay Time | 9 ns |
| Family | CBT/FST/QS/5C/B |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Bandwidth | 200MHz |
| High Level Output Current | -128mA |
| Low Level Output Current | 128mA |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 2 |
| Length | 15.875mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74CBTR16861DLR Overview
In order to save board space, digital switch is located in the 48-BSSOP (0.295, 7.50mm Width).As a result, it is packaged in a way that is referred to as Cut Tape (CT).The method digital switch ic adopts for mounting is Surface Mount.In the multiplexers, the analog IC is indicated by Bus Switch.As long as the operating temperature is -40°C~85°C, turn signal switch will not be influenced by external factors.With a supply voltage of 4.5V~5.5V, designers have greater flexibility of digital controlled switch.Several applications are possible for 74CBTR series multiplexers.Among its basic configurations are 48 terminations.There is a base part number of 74CBTR16861 which can also be used in order to locate the logic switch that are related to this item.The multiplexer is supplied with 5V voltage.This turn signal switch has a total of 48 component pins.Using the point GULL WING as an end point of conductors, it is used to determine the terminus of a conductor.The supply type of this multiplexer ic is Single.There are 48 pins on it.As you can see, it is mounted in the direction of Surface Mount.The logic switch is a member of the CBT/FST/QS/5C/B family.Signal multiplexer contains 20 bits.Keep Vsup at 4V to avoid unnecessary failures.For mux switch's normal operation, there is a power supply provided at 5V.Bus Driver/Transceivers is the classification for this the digital switch ic.It consumes 3μA current of multiplexer ic without external influences.If the supply voltage is set to 5V, reliable performance of the multiplexers can be achieved.The signal switching operates with a resistance of 2.In terms of resistance, it has a value of 50Ohm.Higher switches' flexibility is provided by providing 64mA as the output current.
SN74CBTR16861DLR Features
Supplied in the 48-BSSOP (0.295, 7.50mm Width) package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
SN74CBTR16861DLR Applications
There are a lot of Texas Instruments SN74CBTR16861DLR Signal Switches / Multiplexers / Decoders applications.
- Home automation system
- Arithmetic Logic Units
- Relay
- Code converters
- Solenoid cooling fan
- Electronically controlled engine system
- Transmission from the computer system of a satellite
- Microprocessor memory systems
- Metal detectors
- High-performance memory-decoding applications
