SN74CBTS6800DWR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | 74CBTS |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | Bus Switch |
| Resistance | 7Ohm |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | 74CBTS6800 |
| Pin Count | 24 |
| Operating Supply Voltage | 5V |
| Circuit | 10 x 1:1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Ports | 2 |
| Nominal Supply Current | 250mA |
| Output Current | 64mA |
| Number of Bits | 10 |
| Throw Configuration | SPST |
| Propagation Delay | 250 ps |
| Quiescent Current | 3μA |
| Turn On Delay Time | 6 ns |
| Family | CBT/FST/QS/5C/B |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| High Level Output Current | -128mA |
| Low Level Output Current | 128mA |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 1 |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74CBTS6800DWR Overview
Due to the fact that it is provided in the 24-SOIC (0.295, 7.50mm Width), digital switch allows the board to be compacted.It is packaged in the way of Cut Tape (CT).For mounting, digital switch ic uses the method Surface Mount.As the analog part, the circuit uses an analog IC Bus Switch.A temperature of -40°C~85°C will not leave the turn signal swturn signal switchch susceptible to external influences.When operated with a 4.5V~5.5V supply voltage, digital controlled switch provides digital controlled switch's superior flexibility for designers.In addition to being a member of the 74CBTS series, these multiplexers have a wide range of applications.There is a design for terminating 24 as part of its basic configuration.Its logic switch base part number is 74CBTS6800 which can also be used to find its logic switch related parts.The turn signal switch is supplied with a voltage of 5V volts.This turn signal switch consists of 24 component pins.GULL WING is used as the point at which the conductors come to an end as part of this formula.There is a type of supply of Single.Currently, it is configured with a 24 pin configuration.The multiplexer ic is mounted in the direction of Surface Mount.The logic switch belongs to the family of CBT/FST/QS/5C/B.There are 10 bits signal multiplexer provides.In order to prevent unnecessary failures, it is recommended that the minimal supply voltage (Vsup) be kept at 4V.During mux switch's normal operation, 5V is provided with a power supply.The part belongs to the Bus Driver/Transceivers category of signal switches.It consumes 3μA current of multiplexer ic since it is not affected by external factors.The performance of the multiplexers of a system can be reliably achieved with a supply voltage of 5V.The resistance of the signal switching is 2.With a resistance of 7Ohm, it operates.For higher switches' flexibility, the output current is set to 64mA.
SN74CBTS6800DWR Features
Supplied in the 24-SOIC (0.295, 7.50mm Width) package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
SN74CBTS6800DWR Applications
There are a lot of Texas Instruments SN74CBTS6800DWR Signal Switches / Multiplexers / Decoders applications.
- Analog to digital conversion
- Signal router
- Enabling different functions units in microprocessor instruction decoding
- Image transmission
- Telephone network
- Data collection system
- Paper plants
- Arithmetic Logic Units
- Speed synchronization of multiple motors in industries
- Make full adder
