SN74F109DRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 150MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 20mA |
| Number of Bits | 2 |
| Propagation Delay | 8 ns |
| Turn On Delay Time | 3 ns |
| Family | F/FAST |
| Logic Function | AND, Flip-Flop, JK-Type |
| Logic IC Type | J-KBAR FLIP-FLOP |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Output Lines | 1 |
| fmax-Min | 90 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74F109DRE4 Overview
The item is packaged in SOICcases. It is included in the package Tape & Reel (TR). T flip flop uses TTLas the output. A total of 2elements are contained within it. Terminations are 16. A voltage of 5V is used as the power supply for this D latch. Devices in the F/FASTfamily are electronic devices. A part of the electronic system is mounted in the way of Surface Mount. 16pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. It is designed with a number of bits of 2. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. A power supply of 5Vis required to operate it. Optimal efficiency requires a supply voltage of 5V. It is designed with 1 output lines. -1mAis set as the high level output current. It is set to 20mAfor the low level output current. It is recommended that the operating temperature be lower than 70°C. If the operating temperature is higher than 0°C, the system should operate properly. It is powered by 4.5V as its minimum supply voltage. A maximum voltage of 5.5V can be provided by it. It is possible to obtain a frequency of 150MHz. J-KBAR FLIP-FLOPis the logic IC it uses. Currently, it is equipped with 2 functions . With 16 pins, it is equipped with a low power consumption. 20mA provides maximum design flexibility due to its output current.
SN74F109DRE4 Features
Tape & Reel (TR) package
16 pins
2 Bits
5V power supplies
2 Functions
16 pin count
SN74F109DRE4 Applications
There are a lot of Texas Instruments SN74F109DRE4 Flip Flops applications.
- CMOS Process
- EMI reduction circuitry
- Digital electronics systems
- Supports Live Insertion
- Parallel data storage
- Count Modes
- Latch-up performance
- Data storage
- Modulo – n – counter
- Buffered Clock
