SN74F374DWE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latches |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 100MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 3.2 ns |
| Family | F/FAST |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -3mA |
| Low Level Output Current | 24mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74F374DWE4 Overview
As a result, it is packaged as SOIC. It is configured with TTLas an output. The element count is 1 . 20terminations have occurred. A voltage of 5V is used as the power supply for this D latch. It is a member of the F/FASTfamily of D flip flop. Surface Mount mounts this electronic component. With its 20pins, it is designed to work with most electronic flip flops. Its clock edge trigger type is Positive Edge. It is included in FF/Latches. A total of 5V power supplies are needed to run it. The flip flop has 2embedded ports. High efficiency requires the supply voltage to be maintained at 5V. There are 3 output lines in this JK flip flop. High level output current is set to -3mA. In the low level output current setting, 24mAis used. Ideally, the operating temperature should be below 70°C. It is recommended that the operating temperature be greater than 0°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. A maximum voltage of 5.5V can be provided by it. This can be achieved at a frequency of 100MHz. There is a logic IC BUS DRIVER used in the D flip flop. There are 1 functions available on this T flip flop. It is equipped with 20 pins. In addition to its maximum design flexibility, the output current of the flip flop is 24mA.
SN74F374DWE4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74F374DWE4 Applications
There are a lot of Texas Instruments SN74F374DWE4 Flip Flops applications.
- Storage registers
- Counters
- Divide a clock signal by 2 or 4
- Synchronous counter
- Automotive
- Dynamic threshold performance
- Circuit Design
- Data Synchronizers
- CMOS Process
- Computers
