SN74F374DWR
| Parameters | |
|---|---|
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74F |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74F374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 3.2 ns |
| Family | F/FAST |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 3mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
SN74F374DWR Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. You can find it in the Cut Tape (CT)package. This output is configured with Tri-State, Non-Inverted. It is configured with the trigger Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. Temperature is set to 0°C~70°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the 74F series. There should be no greater frequency than 100MHzon its output. In total, it contains 1 elements. There have been 20 terminations. If you search by 74F374, you will find similar parts. A voltage of 5V provides power to the D latch. In terms of electronic devices, this device belongs to the F/FASTfamily of devices. This electronic part is mounted in the way of Surface Mount. There are 20pins on it. It has a clock edge trigger type of Positive Edge. The part is included in FF/Latches. Flip flops designed with 8bits are used in this part. The superior flexibility of this product is achieved by using 8 circuits. This D flip flop is well suited for TR based on its reliable performance. It operates from 5V power supplies. The flip flop has 2ports embedded within it. In order to ensure high efficiency, the supply voltage should remain at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. To operate, the chip has a total of 3 output lines.
SN74F374DWR Features
Cut Tape (CT) package
74F series
20 pins
8 Bits
5V power supplies
SN74F374DWR Applications
There are a lot of Texas Instruments SN74F374DWR Flip Flops applications.
- CMOS Process
- Storage registers
- Frequency division
- Test & Measurement
- Power down protection
- Reduced system switching noise
- Control circuits
- Supports Live Insertion
- Data transfer
- Buffer registers
