SN74F377ADWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 125MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Current - Output | 20mA |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 6.5 ns |
| Family | F/FAST |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.02 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Power Supply Current-Max (ICC) | 90mA |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74F377ADWG4 Overview
The package is in the form of SOIC. There is a TTLoutput configured with it. In total, it contains 1 elements. 20terminations have occurred. It is powered from a supply voltage of 5V. In terms of electronic devices, this device belongs to the F/FASTfamily of devices. There is an electronic part mounted in the way of Surface Mount. A total of 20pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. As a result of its reliable performance, this T flip flop is suitable for TUBE. The power supply is 5V. In order to achieve high efficiency, the supply voltage should be maintained at 5V. It is also characterized by WITH HOLD MODE. The high level output current is set to -1mA. Low level output current is set to 20mA. It is recommended that the operating temperature be lower than 70°C. Temperatures above 0°Cshould be used. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. A maximum voltage of 5.5V can be provided by it. It is possible to achieve a frequency of 125MHz. The logic IC it uses is D FLIP-FLOP. A total of 1 functions are provided by this T flip flop. The D latch is equipped with 20 pins. It offers maximum design flexibility with its output current of 20mA.
SN74F377ADWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74F377ADWG4 Applications
There are a lot of Texas Instruments SN74F377ADWG4 Flip Flops applications.
- Differential Individual
- Buffered Clock
- Test & Measurement
- Latch-up performance
- Set-reset capability
- Computing
- Frequency Dividers
- Parallel data storage
- Communications
- Single Down Count-Control Line
