SN74F74NSRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOP |
| Number of Pins | 14 |
| Weight | 208.312296mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 145MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Current - Output | 20mA |
| Number of Bits | 1 |
| Propagation Delay | 8 ns |
| Turn On Delay Time | 3 ns |
| Family | F/FAST |
| Logic Function | AND, D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | 20mA |
| Low Level Output Current | 1mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74F74NSRE4 Overview
In the form of SOP, it has been packaged. You can find it in the Tape & Reel (TR)package. Currently, the output is configured to use TTL. In total, it contains 2 elements. It has been determined that there have been 14 terminations. A voltage of 5V provides power to the D latch. Devices in the F/FASTfamily are electronic devices. Electronic part Surface Mountis mounted in the way. Basically, it is designed with a set of 14 pins. This device has Positive Edgeas its clock edge trigger type. This RS flip flops is a part number FF/Latches. 1bits are used in its design. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. The system runs on a power supply of 5V watts. For high efficiency, the supply voltage should be kept at 5V. It has 3 output lines to operate. 1input lines are available for you to choose from. 20mAis the output current at high level. There is no low level output current set at 1mA. It is recommended that the operating temperature be lower than 70°C. It should be higher than 0°Cwhen the system is operating. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis its maximum supply voltage. We are able to achieve a frequency of 145MHz. It uses the logic IC D FLIP-FLOP. There are 2 functions associated with the JK flip flop. It has 14 pins. Its output current of 20mA allows for maximum design flexibility.
SN74F74NSRE4 Features
Tape & Reel (TR) package
14 pins
1 Bits
5V power supplies
2 Functions
14 pin count
SN74F74NSRE4 Applications
There are a lot of Texas Instruments SN74F74NSRE4 Flip Flops applications.
- Reduced system switching noise
- Frequency Divider circuits
- Individual Asynchronous Resets
- High Performance Logic for test systems
- Automotive
- Circuit Design
- Guaranteed simultaneous switching noise level
- Test & Measurement
- Divide a clock signal by 2 or 4
- Storage registers
